Gaming Tech

Uniformation GKtwo evaluation:

Uniformation GKtwo evaluation:

The Uniformation GKtwo is simply what I wanted – and it solves one of many largest points most of the finest 3D printers have.

Except you have acquired your heating on blast always otherwise you run a small enterprise with half a dozen machines pumping out fashions – to not point out warmth – by the truckload, you in all probability have a troublesome time holding your printer toasty in winter. Once I was simply beginning out, I could not fathom why the miniatures I used to be making an attempt to create would fail as quickly as that seasonal chilly set in. The settings had labored completely earlier than, so what had gone improper? Chilly climate, that is what. I finally realized that low temperature would change how resin reacts, lengthening curing time consequently and sometimes ruining prints should you do not modify your settings accordingly. Besides you do not have to with the Uniformation GKtwo. Its inbuilt heating system is not a silver bullet, however it’s a step in the appropriate path for certain.

This can be a good reminder that you simply needn’t persist with the largest manufacturers on the subject of 3D printing – lesser-known corporations like Uniformation are price your time too.

Uniformation GKTwo – options & design

Swipe to scroll horizontally
Value $849.99
Printer sort Resin
Decision 8K (7680*4320px, 29.6μm XY)
Display screen 10.3″ Monochrome LCD
Printing quantity 6.7L/226.5oz.
Leveling Handbook

That heating system is not the one feather within the GKtwo’s hat. Alongside a display able to 8K decision and a construct quantity of 10.3 inches for bigger fashions, it incorporates a built-in air air purifier positioned barely larger than opponents (which stops it from being splashed with resin ought to one thing go improper) and an easy-release system for its vat and construct plate. The vat particularly is rather a lot simpler to take out than different machines as a result of it largely slides into place earlier than slotting in place because of a pair of toes on the again.

Different sensible design decisions are the USB slot on the entrance beside the touchscreen (side-mounted ones are at all times a nuisance to entry) and a hinged cowl that lifts upward. This avoids the necessity to pull the whole cowl off and discover someplace to place it.

It will not remedy the entire neighborhood’s issues and you may’t function it in an icebox, however it’s fairly rattling good nonetheless

By way of design, the GKtwo is a good-looking beast that instantly differentiates itself from its friends because of the hatch on the entrance. The resin vat and construct plate take some getting used to as a result of they’re so completely different (and rather a lot chunkier on the whole), however they don’t seem to be ‘unhealthy’ by any means.

Uniformation GKtwo – efficiency

window.sliceComponents = window.sliceComponents || {};

externalsScriptLoaded.then(() => {
window.reliableDOMContentLoaded.then(() => {
var componentContainer = document.querySelector(“#slice-container-fzucdENvZTmRE5VE4rHBqW-imageGallery-9”);

if (componentContainer) {
var data = {“galleryData”:[{“title”:””,”description”:[],”image”:{“id”:”xxQKVMBf8QV2tfYbPTuXbZ”,”name”:”Printer.jpg”,”credit”:{“text”:”(Image credit: {subject})”,”subject”:”Benjamin Abbott”},”src”:””,”alt”:”Uniformation GKtwo lid open”,”width”:1920,”height”:1080,”srcSetSizes”:[320,480,650,970,1024,1200],”sizes”:{“default”:”calc(100vw – 40px)”,”1000px”:”970px”},”fullscreen”:false,”lazyLoading”:true,”addSEOMetaData”:false,”eager”:false,”removeNativeWidthRestriction”:false,”dataBordeauxImageCheckAttr”:false,”noCredit”:false}},{“title”:””,”description”:[],”image”:{“id”:”e64dovNmT737Pha4y8274Z”,”name”:”Printer4.jpg”,”credit”:{“text”:”(Image credit: {subject})”,”subject”:”Benjamin Abbott”},”src”:””,”alt”:”Uniformation GKtwo build plate”,”width”:1920,”height”:1080,”srcSetSizes”:[320,480,650,970,1024,1200],”sizes”:{“default”:”calc(100vw – 40px)”,”1000px”:”970px”},”fullscreen”:false,”lazyLoading”:true,”addSEOMetaData”:false,”eager”:false,”removeNativeWidthRestriction”:false,”dataBordeauxImageCheckAttr”:false,”noCredit”:false}},{“title”:””,”description”:[],”image”:{“id”:”cSJMCxHZbmuSKTWWzKfwfY”,”name”:”Printer3.jpg”,”credit”:{“text”:”(Image credit: {subject})”,”subject”:”Benjamin Abbott”},”src”:””,”alt”:”Uniformation GKtwo resin vat”,”width”:1920,”height”:1080,”srcSetSizes”:[320,480,650,970,1024,1200],”sizes”:{“default”:”calc(100vw – 40px)”,”1000px”:”970px”},”fullscreen”:false,”lazyLoading”:true,”addSEOMetaData”:false,”eager”:false,”removeNativeWidthRestriction”:false,”dataBordeauxImageCheckAttr”:false,”noCredit”:false}}],”progressText”:”Image {currentSlide} of {totalSlides}”,”viewOriginalText”:”View Original”};

var triggerHydrate = function() {
window.sliceComponents.imageGallery.hydrate(data, componentContainer);

var triggerScriptLoadThenHydrate = function() {
if (window.sliceComponents.imageGallery === undefined) {
var script = document.createElement(‘script’);
script.async = true; = ‘vanilla-slice-fzucdENvZTmRE5VE4rHBqW-imageGallery-9-component-script’;

script.onload = () => {
window.sliceComponents.imageGallery = imageGallery;
} else {

if (window.lazyObserveElement) {
window.lazyObserveElement(componentContainer, triggerScriptLoadThenHydrate, 1500);
} else {
console.log(‘Could not lazy load slice JS for fzucdENvZTmRE5VE4rHBqW-imageGallery-9’)
}).catch(err => console.log(‘Hydration Script has failed for fzucdENvZTmRE5VE4rHBqW-imageGallery-9 Slice’, err));
}).catch(err => console.log(‘Externals script failed to load’, err));

  • Heater works brilliantly
  • Good-quality prints
  • Ease-of-use options are a standout
  • Construct plate is usually a ache when cleansing

I used to be actually impressed with this printer; the Uniformation GKtwo was in a position to produce a great deal of high-fidelity, high-quality miniatures with out fuss. As soon as I might leveled the factor, it smashed via any undertaking large and small that I threw at it. Smaller characters for the very best tabletop RPGs? No drawback. Bigger monsters for Dungeons and Dragons books? Certain factor. 

Due to that inbuilt heater (which may convey the temperature up “95 ℉ in eight minutes if the present ambient temperature is 50 ℉,” in keeping with Uniformation), I by no means had any points with my resin. It will not remedy the entire neighborhood’s issues and you may’t function it in an icebox, however it’s fairly rattling good nonetheless.

On a equally sensible be aware, I discovered the GKtwo to be fairly strong as effectively. The hinged entrance is a lot simpler than the lift-off lids of most printers (such because the in any other case glorious Elegoo Saturn 3 Extremely 12K), largely as a result of you do not have to fret about placing it anyplace. As well as, the slide-out resin vat is far much less of a faff to make use of than the conventional ones that use screws (which might be awkward to show in case your gloves are a bit slippery with resin).

A be aware on value

Uniformation GKtwo machine and packaging

(Picture credit score: Benjamin Abbott)

I ought to level out that alongside the $800-odd price ticket for the machine, getting the wash and treatment kits can be fairly an expense. The latter two are bought individually and getting all of it collectively from Uniformation will set you again a barely eye-watering $1,259.97.

I’ve to confess that it isn’t all hunky-dory, in fact. As an illustration, the chunky construct plate (it is a lot thicker than you will be used to) is extra of a fuss to degree as a result of it requires a number of screws to be turned in reverse instructions. As well as, not having a perfectly-sized cleansing equipment – I wasn’t despatched an identical Uniformation one for my evaluation – implies that you will have to dunk it into your IPA somewhat than laying it on the highest. This causes the plate to fill with fluid, that means you will have to take a seat and drain it earlier than transferring on. That is not a complete catastrophe and you will in all probability have the appropriate cleansing tub to go together with the GKtwo anyway (I might advise it), however the level is, do not attempt to bodge an answer like I did. You are higher off getting the official companion for the machine… however that is a disgrace as a result of all of it provides up when it comes to value.

It improves on present programs because of that very useful heating system. I hope to see that in additional printers going ahead

I had some issues revolving across the resin vat’s design as effectively, largely as a result of I used to be involved about extra being caught on the raised components somewhat than filling the middle. However there have been no points ultimately, and that additional area did assist keep away from spillage if I moved the vat too rapidly throughout elimination.

Must you purchase the Uniformation GKtwo?

Uniformation GKtwo machine and power pack, along with a box of useful items

(Picture credit score: Benjamin Abbott)

For probably the most half, I used to be very impressed with the Uniformation GKtwo. It does precisely what it says on the tin and people prints come out wanting unbelievable even on probably the most primary settings. Extra importantly, although, it improves on present programs because of that very useful heating system. I hope to see that in additional printers going ahead.

Now we simply want Uniformation3D so as to add a self-leveling construct plate and 12K just like the Anycubic Photon Mono M5s… For the GKthree, maybe? 

Purchase it if…

Temperature is an issue for you: That heated system is an actual gem, negating lots of points you may in any other case have when 3D printing. You will not want to fret as a lot about printing in winter anymore.

✅ You desire a extra sensible system: The short-release vat and hinged entrance are a lot simpler to make use of than opponents’ options. I might fairly wish to see the identical on fashions from Anycubic, Elegoo, and past.

Do not buy it if…

You wish to print in 12K: Sadly, the GKtwo solely prints in 8K. That is not damning by any means, however if you need the very best decision potential, you will have to look elsewhere.

You do not wish to purchase a brand new cleansing system: As a result of it is a bit awkward to make use of on a competitor’s cleansing equipment (the construct plate could replenish with fluid if you must dunk the entire thing, for instance), it is higher to get Uniformation3D’s system – and it’s possible you’ll not wish to do this contemplating the price of the GKtwo.

Uniformation GKtwo alternate options

Not feeling this one? On the time of writing, I am unable to see any programs that even have an inbuilt heater. In need of shopping for extras so as to add into your present machine, you are caught with the GKtwo. 

Naturally, there are many different choices if you need 8K prints – the Anycubic Photon M3 Premium, for instance. It has an identical build-space to the GKtwo, and though it would not characteristic the identical ease-of-use additions when it comes to resin vat, it does embrace two air purifiers. 

How we examined the Uniformation GKtwo

After receiving the machine and setting it up, I used it to print off miniatures of various sizes from Forged n Play, Titan Forge, Artisan Guild, and extra over a few weeks. These ranged between smaller 28mm / 32mm characters, bigger monsters, and surroundings. Sadly, we could not use Uniformation3D resin as a result of it wasn’t out there on the time. I additionally ended up utilizing an present Elegoo wash and treatment system as a result of I wasn’t supplied with a Uniformation model.

You could find out extra about our course of by way of our information to how we check.


This evaluation unit was offered by Uniformation.

For concepts on what to print subsequent, take a look at the way to 3D print miniatures for D&D and tabletop RPGs.


Back to top button